Atomic Force Microscopy Techniques Research Articles

[Atomic Force Microscopy to Measure the Mechanical Property of Nanosized Lipid Vesicles and Its Applications].

Nanoparticles, including liposomes and lipid nanoparticles, have garnered global attention due to their potential applications in pharmaceuticals, vaccines, and gene therapies. These particles enable targeted delivery of new drug modalities such as highly active small molecules and nucleic acids. However, for widespread use of nanoparticle-based formulations, it is crucial to comprehensively analyze their characteristics to ensure both efficacy and safety, as well as enable consistent production. In this context, this review focuses on our research using atomic force microscopy (AFM) to study liposomes and lipid nanoparticles. Our work significantly contributes to the capability of AFM to measure various types of liposomes in an aqueous medium, providing valuable insights into the mechanical properties of these nanoparticles. We discuss the applications of this AFM technique in assessing the quality of nanoparticle-based pharmaceuticals and developing membrane-active peptides.

Changes of surface properties of sucrose particles during grinding in a cocoa butter-based suspension and their influence on the macroscopic behavior of the suspension

AbstractChocolate mass is a cocoa butter-based suspension, which mainly consists of sugar and cocoa particles dispersed in a continuous lipid phase. During chocolate manufacturing, sugar particles have to be ground to sizes below 25–30 µm. Such a fine grinding is carried out either by five roll refiners or by ball mills. Despite obtaining similar particle size distributions at the end, the grinding procedures result in different chocolate mass properties. The reasons for that are not fully understood, so far. Therefore, changes in particle sizes and surface properties of sucrose particles as well as their interactions with surrounding cocoa butter during the different grinding processes were investigated including atomic force microscopy techniques to characterize local surface states. It was found that especially the alteration of surfaces during continued grinding differed. In the case of roller grinding, surface states became more inhomogeneous and different surfaces states at microscopic level existed in parallel. More homogenous surfaces but with a higher degree of amorphous states were formed during grinding in the ball mill. Variations in macroscopic behavior of the suspension can be explained by the differences in interaction of particles with each other and with the surrounding lipid phase.

Synthesis and characterization of nano-biocomposite (PMMA-hydroxyapatite - CaZrO3) for bone tissue engineering

ABSTRACT In a common scenario, bone fractures have a self-healing function with free-surgical intervention. However, some fractures in bone tissue are complex and leave behind remnant deformation that requires biomaterials for replacement. The aim of this study is to develop a new composite 3D scaffold for bone regeneration and replacement composed of calcium zirconate (CaZrO3), hydroxyapatite (HA) and polymethylmethacrylate (PMMA) polymer. Different 3D scaffolds were fabricated by mixing 90, 80, 70, and 60 wt. % PMMA with HA and CaZrO3 nanoparticles in different concentrations. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM) techniques were applied to characterize the 3D composite scaffold properties. Furthermore, the mechanical properties of the fabricated scaffolds were investigated using Brazilian diametral fracture test. It was found that incorporating a uniform distribution of HA nanoparticles significantly increased the surface roughness of the composite scaffold. Furthermore, the fracture strength of the fabricated 3D scaffolds showed a remarkable improvement of 86% in the sample containing 90% PMMA, 7% HA, and 3% CaZrO3 compared to the sample devoid of CaZrO3. Our findings strongly indicate that integrating hybrid CaZrO3-HA nanoparticles into PMMA polymer for the production of 3D composite scaffolds holds significant promise for bone tissue applications, potentially enhancing their efficacy and performance.

Gamma irradiated Cu-doped TiO2 nanoparticles for selective ammonia sensing

In this research, the effect of gamma ray doses on volatile organic compound (VOC) sensing properties of Cu doped TiO2 nanoparticles are studied to further improve the VOC sensing performance. Pure and Cu doped TiO2 nanoparticles have been prepared by sol-gel technique on Au interdigitated plexiglas substrate and irradiated by gamma-rays with doses varying from 1 to 150 KGy. The irradiation was performed by using 60Co as gamma source. The structural, morphology and modifications were analyzed with X-ray diffraction (XRD), scanning electron microscopy (SEM), and Atomic Force Microscopy (AFM) techniques. The sensing performance of these films toward ethanol, methanol, 2-propanol, benzene, toluene, xylene and ammonia vapors has been tested. It was observed that no remarkable sensor response to any vapors except ammonia was observed at room temperature. Changes in sensor’ ammonia sensitivity have been correlated with the gamma radiation dose and Cu doping ratio. Maximum sensing performance was observed with 3% Cu doped TiO2 exposed to gamma radiation dose of 150 kGy.

Xyloglucan deficiency leads to a reduction in turgor pressure and changes in cell wall properties, affecting early seedling establishment.

Xyloglucan is believed to play a significant role in cell wall mechanics of dicot plants. Surprisingly, Arabidopsis plants defective in xyloglucan biosynthesis exhibit nearly normal growth and development. We investigated a mutant line, cslc-Δ5, lacking activity in all five Arabidopsis cellulose synthase like-C (CSLC) genes responsible for xyloglucan backbone biosynthesis. We observed that this xyloglucan-deficient line exhibited reduced cellulose crystallinity and increased pectin levels, suggesting the existence of feedback mechanisms that regulate wall composition to compensate for the absence of xyloglucan. These alterations in cell wall composition in the xyloglucan-absent plants were further linked to a decrease in cell wall elastic modulus and rupture stress, as observed through atomic force microscopy (AFM) and extensometer-based techniques. This raised questions about how plants with such modified cell wall properties can maintain normal growth. Our investigation revealed two key factors contributing to this phenomenon. First, measurements of turgor pressure, a primary driver of plant growth, revealed that cslc-Δ5 plants have reduced turgor, preventing the compromised walls from bursting while still allowing growth to occur. Second, we discovered the conservation of elastic asymmetry (ratio of axial to transverse wall elasticity) in the mutant, suggesting an additional mechanism contributing to the maintenance of normal growth. This novel feedback mechanism between cell wall composition and mechanical properties, coupled with turgor pressure regulation, plays a central role in the control of plant growth and is critical for seedling establishment in a mechanically challenging environment by affecting shoot emergence and root penetration.

Multiparametric AFM insights into electron transport mechanisms in biomemristors

Biomemristors have attracted significant attention due to their applications in biodegradable and flexible electronic devices, and their prospective functions in information storage, neural synapses, and neuromorphic computation. Hence, understanding biomaterials' resistive switching (RS) mechanism is essential to design novel biomemristors with enhanced performance. In the last decade, various atomic force microscopy (AFM) modes, such as Kelvin probe force microscopy (KPFM) and conductive atomic force microscopy (cAFM), in situ/operando visualize the electron transport behaviors within biomemristors at the nanoscale. This review provides a comprehensive discussion of multiparametric AFM techniques to characterize biomemristors and inspire new ideas in developing next-generation consumer electronics. We also summarize the progress of revealing the internal mechanism of biomemristors with functional AFM to visualize and understand the switching behavior. Finally, the opportunities and challenges of further utilizing multiparametric AFM to explore the electron transport mechanisms in biomemristors are presented.

Insights into the dual nature of αB-crystallin chaperone activity from the p.P39L mutant at the N-terminal region

The substitution of leucine to proline at position 39 (p.P39L) in human αB-crystallin (αB-Cry) has been associated with conflicting interpretations of pathogenicity in cataracts and cardiomyopathy. This study aimed to investigate the effects of the p.P39L mutation on the structural and functional features of human αB-Cry. The mutant protein was expressed in Escherichia coli (E. coli) and purified using anion exchange chromatography. We employed a wide range of spectroscopic analyses, gel electrophoresis, transmission electron microscopy (TEM), and atomic force microscopy (AFM) techniques to investigate the structure, function, stability, and fibrillation propensity of the mutant protein. The p.P39L mutation caused significant changes in the secondary, tertiary, and quaternary structures of human αB-Cry and increased the thermal stability of the protein. The mutant αB-Cry exhibited an increased chaperone activity and an altered oligomeric size distribution, along with an increased propensity to form amyloid aggregates. It is worth mentioning, increased chaperone activity has important positive and negative effects on damaged cells related to cataracts and cardiomyopathy, particularly by interfering in the process of apoptosis. Despite the apparent positive nature of the increased chaperone activity, it is also linked to adverse consequences. This study provides important insights into the effect of proline substitution by leucine at the N-terminal region on the dual nature of chaperone activity in human αB-Cry, which can act as a double-edged sword.

Abstract 496: Insights into correlation between nanomechanical properties and cytokines expression during gold nanoparticle endocytosis

Abstract Gold nanoparticles for therapeutic interventions have become a widely popular source due to the ease in surface chemistry available for modification. Several studies undertaken focusses on the size, shape of nanoparticles as well as the signaling mechanisms and yet, knowledge regarding the alteration in membrane dynamics such as nanomechanical properties and cytokines involved during their uptake has not been studies before. To overcome the knowledge deficit, we employed atomic force microscopy and qRT-PCR techniques to acquire nanomechanical attributes and cytokines expressions respectively, in Panc-1 and AsPC-1 cell lines treated with surface modified gold nanoparticles for 1- and 24-hours’ time point. In nanomechanics paradigm, impetus was given on both linear attributes such as membrane stiffness, deformation, and adhesion as well as non-linear attributes such as drained Poisson’s ratio, diffusion coefficient and pore size. On the other hand, qRT-PCR technique yielded alterations in relative mRNA expressions of pro-tumorigenic cytokines such as CCL2, CXCL1, CXCL2, CXCL3, IL8, IL11, IL18 and TGFβ-1. Further, using Pearson’s correlation, we deduced the dependency between nanomechanical properties and cytokines expressions. We evaluated several criteria such as receptor dependent vs independent, PEGylated vs non-PEGylated and 1 hr vs 24hrs, to deduce correlations between cytokines and nanomechanical attributes. In Panc-1 cell line, we observed that PEGylation vs non-PEGylation of gold nanoparticles demonstrated most significant correlations, whereas in AsPC-1 cell line, receptor independent mechanism played a pivotal role in establishing significant correlations. For instance, D_C and P_D were highly correlated with CXCL1, CXCL2 and TGFβ-1 when non-PEGylated gold nanoparticles were up taken by Panc-1 cells. Similarly, D_C and P_D were highly correlated consistently with our cytokine panel except for TGFβ-1. In AsPC-1 cell line, deformation was significantly correlated with CCL2, CXCL2, CXCL3 and IL-8 whereas, D_C and P_D were significantly correlated with CCL2, CXCL1, CXCL3, IL-18 and TGFβ-1 in receptor independent scenario. This study demonstrated that during the uptake of gold nanoparticles, non-linear nanomechanical attributes are detrimental over linear attributes. Moreover, Surface modified gold nanoparticles induce varying levels of alteration in pro-tumorigenic cytokines. Taken together, this study boosts our insights into correlations describing cytokines regulating nanomechanical attributes in endocytosis paradigm. Citation Format: Tanmay Kulkarni, Enfeng Wang, Ramcharan Singh Angom, Debabrata Mukhopadhyay, Santanu Bhattacharya. Insights into correlation between nanomechanical properties and cytokines expression during gold nanoparticle endocytosis [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2024; Part 1 (Regular Abstracts); 2024 Apr 5-10; San Diego, CA. Philadelphia (PA): AACR; Cancer Res 2024;84(6_Suppl):Abstract nr 496.

ПОЛУЧЕНИЕ И ИССЛЕДОВАНИЕ ПОЛИМЕРНЫХ НАНОЧАСТИЦ

Currently, there is an increasing interest in the study of polymers in a nanodisperse state. Since polymer materials, as a rule, are heterogeneous systems with a sufficiently variable surface, a correct assessment of their chemical structure, physical properties and morphology is of great scientific and practical importance. Polymer nanoparticles (PNPs) have been successfully studied for a long time as nanoscale colloidal particles obtained from polymers. Research on HDPE is most intensively conducted in the field of nanomedicine, and the possible application of HDPE in the field of optoelectronics, photonics, gadgets, sensors, sensors, and new nanocomposites is of great interest to researchers. An independent task is to compare the properties of the HDPE with the properties of a bulk polymer, including the features of its supramolecular structure. Previous studies of the supramolecular structure of PDFs have suggested that charge transfer in the polymer during resistive switching occurs along the grids of intergranular boundaries. This paper presents the results of an experimental study of polymer nanoparticles on different substrates by atomic force microscopy. The main metrological parameters of polymer nanoparticles were determined, the results were compared with the available data on the supramolecular structure of polymer films. The possibility of using atomic force microscopy techniques to visualize polymer nanoparticles on dif- ferent substrates has been demonstrated. Using the AFM method with a conductive probe, it was found that in some cases, during the aggregation of nanoparticles on a metal substrate, charge transfer is realized along separate nanometer-sized sections. The conducting channels in the current image have the form of separate points with a height corresponding to the locally flowing current. It was found that the arrangement of the observed channels correlates well with the model of conductivity along the grain boundaries of the supramolecular structure of the polymer. The issues of interpretation of current images of polymer nanoparticles and the physical model of charge transfer in polymer nanostructures are discussed. The work was carried out with the support of the Mirror Labora- tories project of the National Research University Higher School of Economics and an intra-university grant from the Bashkir State Pedagogical University named after M. Akmulla.

Influence of swift heavy ion irradiation on structure and morphology of La0.25Pr0.375Ca0.375MnO3 film

The effects of Ag15+ (120 MeV) swift heavy ion (SHI) irradiation on the structural and morphological properties of epitaxial La0.25Pr0.375Ca0.375MnO3 (LPCMO) thin films were investigated by x-ray scattering and atomic force microscopy (AFM) techniques. LPCMO films of thickness ∼ 280 Å were irradiated with an Ag15+ ion beam at different fluences of 1 × 1011, 5 × 1011, and 1 × 1012 ions cm−2. XRD results suggested the development of the tensile stress along the out-of-plane direction of the LPCMO film upon ion irradiation, which increases on increasing the ion fluence. The morphology of the film was also modified with the irradiation and an increase in the fluence of the ion beam enhanced the in-plane height-height correlation length scale (grain size) with a loss of the fractal behaviours. The linear variation of microstrain with ion irradiation fluence in thin LPCMO film can be considered for a possible strain-driven application in modifying functional properties of such a phase separated complex oxide.

Optical, conductive, and ferroelectric properties of the first layer of dip-coated BiFeO3 films from methoxyethanol and acetic acid-based chemical dissolvents

The overall performance of the multilayer resulting in a sol-gel bismuth ferrite (BiFeO3) film will be primarily determined by the properties of the first layer, but this has yet to receive much attention, even though chemical and morphological defects of this layer can accumulate as the number of layers increases. Here, we perform an optical, conductive, and ferroelectric study of first layer (L 1) dip-coating sol-gel BiFeO3 films using two routes that vary only in the dissolvent; the first one is based on 2-methoxyethanol (MOE), and the second one on acetic acid (AA) with some MOE (AA-MOE). Tauc plots reveal a band gap of 2.43 eV and 2.75 eV for MOE (30 ± 5 nm thick) and AA-MOE (35 ± 5 nm thick) films, respectively. MOE films showed a dielectric function with features at ∼2.5 eV, ∼3.1 eV, and ∼3.9 eV, which were associated with charge-transfer transitions, but such features are absent in AA-MOE films. Advanced atomic force microscopy techniques were used to identify the fine features or defects of the BiFeO3 films: The conductive maps show that the charge transport pathways in both film routes are controlled by nanometer defects rather than grain or grain boundary defects. Current-voltage curves reveal high conductive pathway at a lower voltage for the MOE films than for AA-MOE films. The piezoelectric coefficient for MOE films was ∼20% higher than AA-MOE films. Both deposition methods yield ferroelectric films with an electromechanical strain controlled by the piezoelectric effect and minimal contribution from electrostriction. An optimization for the AA-MOE-based route in the withdrawal speed results in a significant reduction of morphological defects and a more than twofold increase in the piezoelectric coefficient. Our results broaden the understanding of optical and ferroelectric BiFeO3 films based on a chemical solution by dip-coating.

Investigating the Role of Embedded ZnO Seed Layer Thickness in Electrodeposited Cu2O/Zn(x)Mg(1−x)O/ZnO/FTO Heterojunctions for Photovoltaic Applications

This article represents the construction of Cu2O/Zn(x)Mg(1−x)O/ZnO/FTO heterojunctions by employing a simple electrodeposition approach. The impact of inserting ZnO seed layers with different thicknesses on the various physicochemical properties of the electrodeposited films is explored by applying various techniques. The electrochemical characterization specifies high photoresponses achieving 335.42 μA cm−2 for seeded Cu2O/Zn(x)Mg(1−x)O heterojunctions by increasing the thickness of seeded ZnO layer from 25 to 100 nm. The scanning electron microscopy and atomic force microscopy techniques indicate that the surface texture and smoothness of Cu2O/ZnO heterojunctions have significantly enhanced after increasing the thickness of the ZnO layers. The synthesized ZnO nanostructures are found to be highly crystalline in nature having ZnO with hexagonal phase oriented along (002) direction and Cu2O with cubic structure oriented along (111) direction. This study shows the introduction of ZnO seed layers, enhances the I–V characteristics of Au/Cu2O/Zn(x)Mg(1−x)O/ZnO/FTO solar cells. The ideality factor shows a decreasing tendency from 5.35 to 3.93 while the photoelectric response is increased from 427% to 643% with the increase of the ZnO thickness from 25 to 100 nm, respectively, demonstrating the effectiveness of the seed layers approach.

Periodic Folded Gold Nanostructures with a Sub-10 nm Nanogap for Surface-Enhanced Raman Spectroscopy.

Surface-enhanced Raman spectroscopy has emerged as a powerful spectroscopy technique for detection with its capacity for label-free, nondestructive analysis, and ultrasensitive characterization. High-performance surface-enhanced Raman scattering (SERS) substrates with homogeneity and low cost are the key factors in chemical and biomedical analysis. In this study, we propose the technique of atomic force microscopy (AFM) scratching and nanoskiving to prepare periodic folded gold (Au) nanostructures as SERS substrates. Initially, folded Au nanostructures with tunable nanogaps and periodic structures are created through the scratching of Au films by AFM, the deposition of Ag/Au films, and the cutting of epoxy resin, reducing fabrication cost and operational complexity. Periodic folded Au nanostructures show the three-dimensional nanofocusing effect, hotspot effect, and standing wave effect to generate an extremely high electromagnetic field. As a typical molecule to be tested, p-aminothiophenol has the lowest detection limit of up to 10-9 M, owing to the balance between the electromagnetic field energy concentration and the transmission loss in periodic folded Au nanostructures. Finally, by precisely controlling the periods and nanogap widths of the folded Au nanostructures, the synergistic effect of surface plasmon resonance is optimized and shows good SERS properties, providing a new strategy for the preparation of plasmonic nanostructures.

Controlled Preparation of High Quality Bubble-Free and Uniform Conducting Interfaces of Vertical van der Waals Heterostructures of Arrays.

Sharp and clean interfaces of van der Waals (vdW) heterostructures are highly demanded in two-dimensional (2D) materials-based devices. However, current assembly methods usually cause interfacial bubbles and wrinkles, hindering carrier interlayer transport. The preparation of a large-scale vdW heterostructure with a bubble-free interface is still a challenge. Although many efforts have been made to eliminate bubbles, the evolution processes of the interfacial bubbles are rarely studied. Here, the interface bubble formation and evolution of the transferred 2D materials and their vdW heterostructure are systemically studied by the atomic force microscopy (AFM) technique and high-resolution surface current mapping. A thermal annealing procedure is developed to reduce the number of bubbles and to improve the quality of interfaces. In addition, influences of the interface residues and nanosteps on bubble evolution are also discussed. Further, we develop the polystyrene (PS)-mediated polydimethylsiloxane (PDMS) transfer technique to realize the high-quality transfer of heterostructure arrays. Finally, high-resolution surface current mapping results confirm that we can now produce highly uniform electrical conduction interfaces of heterojunctions. This study provides guidance for assembling high quality interfaces and paves the way for production of bubble-free heterostructure-based electronic devices with high performance and good uniformity.

Adhesion preference of the sticky bacterium Acinetobacter sp. Tol 5.

Gram-negative bacterium Acinetobacter sp. Tol 5 exhibits high adhesiveness to various surfaces of general materials, from hydrophobic plastics to hydrophilic glass and metals, via AtaA, an Acinetobacter trimeric autotransporter adhesin Although the adhesion of Tol 5 is nonspecific, Tol 5 cells may have prefer materials for adhesion. Here, we examined the adhesion of Tol 5 and other bacteria expressing different TAAs to various materials, including antiadhesive surfaces. The results highlighted the stickiness of Tol 5 through the action of AtaA, which enabled Tol 5 cells to adhere even to antiadhesive materials, including polytetrafluoroethylene with a low surface free energy, a hydrophilic polymer brush with steric hindrance, and mica with an ultrasmooth surface. Single-cell force spectroscopy as an atomic force microscopy technique revealed the strong cell adhesion force of Tol 5 to these antiadhesive materials. Nevertheless, Tol 5 cells showed a weak adhesion force toward a zwitterionic 2-methacryloyloxyethyl-phosphorylcholine (MPC) polymer-coated surface. Dynamic flow chamber experiments revealed that Tol 5 cells, once attached to the MPC polymer-coated surface, were exfoliated by weak shear stress. The underlying adhesive mechanism was presumed to involve exchangeable, weakly bound water molecules. Our results will contribute to the understanding and control of cell adhesion of Tol 5 for immobilized bioprocess applications and other TAA-expressing pathogenic bacteria of medical importance.

Nano-positive up negative down in binary oxide ferroelectrics

Ferroelectric HfO2 and ZrO2-based materials are promising candidates for next-generation ferroelectric devices, but their characterization is challenging due to complex factors such as crystal phases, degradation mechanisms, and local inhomogeneities. In this work, we propose a novel nanosized positive-up-negative-down (PUND) method to assess the ferroelectric response of doped-HfO2. This method is based on actual current probing and is immune to most electrostatic artifacts that plague other electrical atomic force microscopy (AFM) techniques. We demonstrate the PUND method’s ability to induce ferroelectric switching in Si-doped HfO2 and investigate the distinctive PUND response obtained for individual grains. We also extract the polarization charge based on a direct estimate of the tip–sample contact area. The proposed PUND method is a significant innovation as it is a method to combine the high spatial resolution of AFM with the immunity to electrostatic artifacts of current probing. This makes it a powerful tool for studying ferroelectric materials at the nanoscale, where local inhomogeneities and other effects can have a significant impact on their behavior. The PUND method is also notable for its ability to extract polarization charge based on a direct estimate of the tip–sample contact area. This is a significant improvement over previous methods, which often relied on indirect or approximate estimates of the contact area. Overall, the PUND method is a novel and innovative technique that offers significant advantages for the characterization of ferroelectric materials at the nanoscale. It is expected to have a major impact on the research and development of next-generation ferroelectric devices.

Exploring the mechanisms of calcium carbonate deposition on various substrates with implications for effective anti-scaling material selection

The unexpected scaling phenomena have resulted in significant damages to the oil and gas industries, leading to issues such as heat exchanger failures and pipeline clogging. It is of practical and fundamental importance to understand the scaling mechanisms and develop efficient anti-scaling strategies. However, the underlying surface interaction mechanisms of scalants (e.g., calcite) with various substrates are still not fully understood. In this work, the colloidal probe atomic force microscopy (AFM) technique has been applied to directly quantify the surface forces between calcite particles and different metallic substrates, including carbon steel (CR1018), low alloy steel (4140), stainless steel (SS304) and tungsten carbide, under different water chemistries (i.e., salinity and pH). Measured force profiles revealed that the attractive van der Waals (VDW) interaction contributed to the attachment of the calcium carbonate particles on substrate surfaces, while the repulsive electric double layer (EDL) interactions could inhibit the attachment behaviors. High salinity and acidic pH conditions of aqueous solutions could weaken the EDL repulsion and promote the attachment behavior. The adhesion of calcite particles with CR1018 and 4140 substrates was much stronger than that with SS304 and tungsten carbide substrates. The bulk scaling tests in aqueous solutions from an industrial oil production process showed that much more severe scaling behaviors of calcite was detected on CR1018 and 4140 than those on SS304 and tungsten carbide, which agreed with surface force measurement results. Besides, high salinity and acidic pH can significantly enhance the scaling phenomena. This work provides fundamental insights into the scaling mechanisms of calcite at the nanoscale with practical implications for the selection of suitable anti-scaling materials in petroleum industries.

High-Speed Near-Surface Tracking for Fast Atomic Force Microscope Scan Switching Based on the Squeeze Film Damping Effect

Atomic force microscope (AFM) is a crucial metrology tool in the semiconductor industry. However, the bottleneck of the AFM technique is its low efficiency, primarily owing to the time-consuming scanning point switching. The traditional method takes approximately one minute for a single switching. To shield the probe and sample, the switching should first lift the probe a considerable distance, move it to the next point, and finally engage the probe slowly to the sample surface. We propose a near-surface tracking method for use in fast scanning point switching. The probe-sample distance was sensed by the squeeze air film damping effect, and the probe was kept at a small constant height during the switching via feedback control. The method can decrease the lift and engage distance from approximately 1 mm to 5 μm, which was two order of reduction; thereby shortening the single switching time from 45 s to 6.1 s, which is an 87% reduction. Generally, the fast switching method can improve the measurement efficiency of the existing AFM working in the air, but it can not be used in liquid and vacuum. Furthermore, the proposed squeeze film damping effect based distance sensing method can be applied in various fields, such as vibration sensing and temperature drift measurement.

Unveiling the molecular interaction of hepatitis B virus inhibitor, entecavir with human serum albumin through computational, microscopic and spectroscopic approaches

Molecular docking, molecular dynamics (MD) simulation, atomic force microscopy (AFM) and multi-spectroscopic techniques were selected to unveil the molecular association between the hepatitis B virus (HBV) inhibitor, entecavir (ETR), and the major blood plasma transporter, human serum albumin (HSA). The entire docking and simulation analyses recognized ETR binding to subdomain IIA (Site I) of HSA through hydrogen bonds, hydrophobic and van der Waals forces while maintaining the complex’s stability throughout the 100 ns. A gradual lessening in the Stern-Volmer quenching constant ( K sv ) with rising temperatures registered ETR-induced quenching of HBV fluorescence as static quenching, thus advising complexation between ETR and HSA. The further advocation of this conclusion was seen from a larger value of the biomolecular quenching rate constant (( kq ) > 1010 M−1s−1), changes in the spectra (UV-Vis absorption) of HSA following ETR inclusion and ETR-induced swelling of HSA in the AFM results. The ETR appeared to bind to HSA with moderate affinity ( K a = 1.87 − 1.19 × 10 4   M−1) at 290, 300 and 310 K. Significant alterations in the protein’s secondary and tertiary structures, including changes in the protein’s Tyr/Trp microenvironment, were also detected by circular dichroism and three-dimensional fluorescence spectra when the protein was bound to ETR. The findings of the drug displacement study backed the docking results of Site I as ETR's preferred binding site in HSA. Communicated by Ramaswamy H. Sarma

Two-Dimensional Tellurium Nanosheets for the Efficient Nonenzymatic Electrochemical Detection of H2O2

This study reports, for the first time, the utilization of two-dimensional (2D) tellurium (Te) nanosheets for the efficient nonenzymatic detection of hydrogen peroxide (H2O2). H2O2 acts as a pivotal biomarker with widespread applications across environmental, biological, industrial, and food processing domains. However, an excessive accumulation of H2O2 in the body poses a severe threat to human life. Consequently, the imperative need for a selective, sensitive, and cost-effective sensing platform for H2O2 detection has gained paramount significance. Employing a low-cost and straightforward hydrothermal method, Te nanosheets were synthesized to address the escalating demand for a reliable detection platform. The as-synthesized Te nanosheets are characterized through Raman spectroscopy and atomic force microscopy techniques. The electrochemical performance of the Te nanosheets integrated onto a glassy carbon (Te-GC) electrode was thoroughly investigated using cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. The experiments were designed to evaluate the response of the Te-GC electrode in the presence and absence of H2O2, alongside its performance in the detection of other pertinent interfering analytes. The sensor shows a limit of detection of 0.47 µM and a sensitivity of 27.2 µA µM−1 cm−2 towards H2O2. The outcomes of this study demonstrate the efficacy of Te nanosheets as a promising material for nonenzymatic H2O2 detection in urine samples. The simplicity and cost-effectiveness of the hydrothermal synthesis process, coupled with the notable electrochemical performance of the Te/GC electrode, highlight the potential of Te nanosheets in the development of a robust sensing platform. This research contributes to the ongoing efforts to enhance our capabilities in monitoring and detecting H2O2, fostering advancements in environmental, biomedical, and industrial applications.